The issue of quality, reliability and safety of the final products is under consideration. Process approach is the base of quality control system, and mon-itoring program is regarded for illustrative purposes.

Keywords: Quality, processor approach, quality management, monitoring

In article traffic safety in intensive transport streams on bridge crossings is considered. In a case when the bridge crossing has on one lane in each direction, at repair of a half of width of the carriageway - density of a transport stream sharply increases. The increase in density of a transport stream leads to change of speed of the movement of vehicles and to reduction of minimum safe distance between the cars moving in the passing direction on the bridge crossing during its repair or reconstruction. At the movement of vehicles with minimum safe distance specified in the table the maximum capacity of the bridge crossing at its repair or reconstruction will be provided.

Keywords: traffic safety, bridge crossing, intensity of the movement, repair of the carriageway, minimum safe distance

The main maintenance of a diversification of production as activity of subjects of managing is considered. being shown in purchase of the operating enterprises, theIn this work, we carried out computer simulations of the equilibrium polarization in the ferroelectric noise within the two-dimensional model Ishibashi in the case of deposits and intra-parietal areas. We considered different configurations influence of thermal noise. The analysis revealed flicker noise in the simulated time dependence of the current strength.

Keywords: simulation, polarization current, domain walls, the noise, Ishibashi model, intra-region, parietal region

Piezoceramic frames made of PKP-12 material with porosity up to 50% are made. The effect of the total, open and closed porosity on the properties of porous piezoelements on a given piezoelectric material is studied. Hydrostatic tests of porous piezoelements have been performed to determine the pressure at which irreversible changes occur.

Keywords: piezoceramics, PKP-12, piezocomposites, porous piezoceramics, piezoelectric materials, ferroelectrics, PZT, hydroacoustics, hydrophone

In the Landau theory of phase transitions taking into account thermal fluctuations of the computer modeling of ferroelectric polarization noise. Based on the spectral analysis, thermal and polarization noise are investigated. The presence of 1 / f noise in the polarization spectrum is detected.

Keywords: ferroelectric, modeling, polarization noise, thermal noise, Fourier transform.

Described trends in the application of two-dimensional-periodic absorbing structures in optical and THz range. The results of calculation of the scatter and reflection of multilayer structures. Designed optimal parameters of the structures to monitor the greatest effect absorption.

Keywords: resonant absorption, plasmons, reflection coefficient, diffraction gratings, periodic structures

The article discusses the technological capabilities of application of vibratory mechanical hard lubricant coatings on the basis of MоS2 to improve the surface quality and operational properties of parts made of aluminum with an oxide coating.

Keywords: vibration treatment, the vibration mechano-chemical coating of solid lubricant, combined methods of treatment

The loops of the dielectric hysteresis of a soft ceramics based on PZT with Curie temperature TC=210℃ are investigated. The studies were carried out at a frequency of 50 Hz in two modes. In the first of them, the field was switched on by 0.07 seconds, in the second - it operated continuously. The amplitude of the field E_m varied from 2.5 to 25 kV / cm and switched stepwise with an interval of 15 minutes. The coercive field EC and the switchable polarization P_m were determined. The switching polarity in the saturation region turns out to be no more, in contrast to BaTiO3 and other materials, but less than the corresponding values obtained with short-term switching.

Keywords: piezoceramics, piezoelectric material, hot pressing, dielectric hysteresis

The article deals with the development of a mathematical model for reducing the cost of building heat storage tanks by using the refrigerating capacity of liquefied natural gas (LNG)

Keywords: liquefied natural gas, LNG, special fortifications, SPS, full isolation mode, heat storage substance, TAB

The article is devoted to the task of searching for the design solution of the structural coating plate. Structural plates are widely used to cover single-storey structures and have a wide variety of structural and architectural forms. The choice of minimum weight design is based on the VAT control method. As the regulators adopted the location of the columns and the class of steel. Depending on the number and location of the columns on which the structural plate rests, the forces in the structural elements change and accordingly the cross-sectional area and mass of the structure change. Four variants of the arrangement of the columns and three versions of the class of steel were considered. For each design variant, the design was calculated numerically, the cross-section was selected, and the mass was determined. Based on the accepted criterion of the effectiveness of the design solution - metal consumption, the most effective design solution was adopted with the arrangement of columns along the perimeter of the coating in steps of one cell.

Keywords: space grid structures for roofs, regulation of stresses, optimization, metal consumption, criterion of optimality

Flat bending stability problem of constant rectangular transverse section wooden beam, loaded by a concentrated force in the middle of the span is considered. Differential equation is provided for the cases when force is located not in the center of gravity. The solution of the equation is generated numerically by the method of finite differences. For the case of applying a load at the center of gravity, the problem reduces to a generalized secular equation. In other cases, the iterative algorithm developed by the authors is implemented, in the package Matlab. A relationship is obtained between the value of the critical force and the position of the load application point. For this dependence, a linear approximating function is chosen. A comparison of the results obtained by the authors with an analytical solution using the Bessel functions is performed.

Keywords: flat bending stability, secular equation, finite difference method, iteration process

The method of calculation gamma percentage fatigue resource of an arrow shovel excavator. Using this method can most accurately determine the distribution of the extreme members of samples and the corresponding shifts of the Weibull distribution. It was found that to calculate the shifts do not have, you can use only the extreme members of samples.

Keywords: reliability, probability, resource, sample, excavator

The article is devoted to the issues of marketing costs evaluation in the construction project cost's management. The methods of determining the marketing cost in the construction sector within the specifics of the industry are issued.

Keywords: marketing costs, project cost management, methods of marketing costs estimation

In this article, we propose methods for designing fault-tolerant structures for Field Programmable Gate Arrays (FPGAs) by forming an internal structure of macro cells (LUTs), with the possibility of correcting single reversible faults in the circuit’s gates. To improve fault tolerance, the failure tolerance of a typical macro cell was assessed, the most vulnerable areas were identified and the most vulnerable parts of the macrocell were protected by means of triple modular redundancy methods. Depending on the expansion of the protected area, various versions of the built-in redundancy were obtained, and various options for minimizing the built-in redundancy were proposed. Experimental work was carried out to form fault-tolerant ISCAS'85 combinational circuit designs in the basis of fault-tolerant FPGAs.

Keywords: combinational circuit, FPGA, field-programmable gate array, LUT, logic synthesis, increase fault tolerant, computer-aided design (CAD), fault injection, single event transient

In the paper, on the basis of the equation of motion of an incompressible lubricant having the micro-polar properties for the case of a ""thin layer"", the equation of continuity, Darcy and the formula for the energy dissipation rate for determining the function Ф (θ), caused by the molten surface of the bearing bush covered with a low-melting metallic melt of a carrier asymptotic solution by the thermal parameter K. Using a self-similar solution for the zeroth approximation, i.e. without taking into account the melt of the low-melting metallic melt, and for the first approximation, taking into account the low-melting metallic melt, the velocity and pressure fields in the lubricating and porous layers are determined, and the basic performance characteristics of the radial slide bearing are determined. The characteristic permeability of the porous layer and the melt of the surface of the bearing bush, coated with a low-melting metallic melt, on the load capacity and frictional force are estimated.

Keywords: low-melting metallic melt, porous layer permeability, lubricant with micro-polar properties, sliding bearing